1. Problems that should be paid attention to before using the hedge trimmer
1. Before using the hedge trimmer, please read the instruction manual carefully to clarify the performance of the machine and the precautions for use.
2. The purpose of the hedge trimmer is to trim hedges and shrubs. In order to avoid accidents, please do not use it for other purposes.
3. The hedge trimmer is equipped with a high-speed reciprocating cutting knife. If it is operated incorrectly, it is very dangerous. Therefore, do not use the hedge trimmer when you are tired or uncomfortable, after taking cold medicine or after drinking alcohol.
4. The engine exhaust contains carbon monoxide which is harmful to the human body. Therefore, do not use hedge trimmers in places with poor ventilation such as indoors, greenhouses or tunnels.
5. Do not use in the following situations.
①When the feet are slippery and it is difficult to maintain a stable working posture.
②When it is difficult to confirm safety around the work site due to dense fog or at night.
③When the weather is bad (rain, strong wind, thunder, etc.).
6. When using it for the first time, be sure to ask an experienced person to give instructions on the use of the hedge trimmer before starting the actual operation.
7. Excessive fatigue will reduce concentration and become the cause of accidents. Do not make the work plan too tight. Each continuous work time cannot exceed 30 to 40 minutes, and then there must be a rest time of 10 to 20 minutes. The work time of the day should be Limited to less than two hours.
8. Minors are not allowed to use hedge trimmers.
2. Labor protection products when using hedge trimmer
1. When using the hedge trimmer, wear clothing suitable for outdoor work, and wear the following protective equipment:
①Working cap (wear a helmet when working on slopes). Long hair should be tied up and protected.
②Dustproof glasses or face shield.
③ Wear sturdy labor protection gloves.
④Shoes that are not slippery and strong.
⑤Earplugs (especially when working for a long time).
2. Be sure to bring the following supplies.
①Machine accessory tools and steel files.
②A spare fuel suitable for hedge trimmers.
③ Replacement blade.
④ Utensils (ropes, wooden signs) for marking the work area.
⑤ Whistle (used when working together or in an emergency).
⑥ Machete, hand saw (used when removing obstacles).
3. Please do not wear wide trousers or bare feet, sandals, straw sandals, etc.
3. Precautions concerning fuel use
1. The fuel used in the engine of the hedge trimmer is a mixture of motor oil and gasoline, which is flammable. Please do not refuel or store fuel in incinerators, burners, stoves and other places that may catch fire.
2. Do not smoke while working or refueling.
3. There is no fuel during use. Be sure to stop the engine first, make sure there are no fireworks around, and then refuel.
4. If fuel is spilled when refueling, be sure to wipe off the fuel attached to the body before starting the engine.
5. After refueling, seal the container, and then start the engine at a place more than 3 meters away from the fuel container.
4. Matters needing attention before work
1. Before starting the operation, it is necessary to understand the conditions of the site (terrain, nature of hedges, location of obstacles, surrounding danger, etc.), and remove obstacles that can be moved.
2. Take the operator as the center and within a radius of 15 meters is a dangerous area. To prevent others from entering this area, ropes or wooden signs must be used to warn the area. In addition, when several people are working at the same time, they should greet each other from time to time and keep a safe distance.
3. Before starting work, check all parts of the machine body carefully, and start work after confirming that there are no loose screws, oil leakage, damage or deformation, etc. In particular, the blades and the connecting parts of the blades should be carefully checked.
4. Make sure that the blade is not chipped, cracked, or bent before use. Never use an abnormal blade.
5. Please use a sharpened blade.
6. When grinding the blade, in order to prevent the blade from chipping, be sure to file the root of the tooth into an arc.
7. After tightening the screw on the blade, first turn the blade by hand to check whether there is up and down swing or abnormal noise. If it swings up and down, it may cause abnormal vibration or loosening of the fixed part of the blade.
|
